VBA-4E4A-CB10-ZEJ/E0J-FL PEPPERL+FUCHS - Part number: 324473

Datasheet excerpt: Technical data of  VBA-4E4A-CB10-ZEJ/E0J-FL Product Description Printed circuit board module4 inputs/4 outputs General specifications Node typeA/B node AS-Interface specificationV3.0 Required master specification≥ V3.0 UL File NumberE223772 MTBF267 a Indicators/operating means LED FAULTerror display; LED redred: communication error or address is 0red flashing: overload of outputs LED PWRAS-Interface voltage; green LEDgreen: voltage OKflashing green: address 0 LED INswitching state (input); 4 LED yellow LED OUTSwitching state (output); 4 LED yellow Electrical specifications Rated operating voltage26.5 ... 31.6 V from AS-Interface (PELV) Rated operating current≤ 40 mA (without inputs/outputs)/max. 160 mA Protection classIII Surge protectionUe: overvoltage category II, safe isolated power supplies (PELV) Input Number/Type4 inputs for mechanical contacts or 3-wire sensors (PNP), DC Supplyfrom AS-Interface Voltage12 ... 31 V Current loading capacity≤ 100 mA Total including output current, overload and short-circuit proof Input current≤ 4 mA (limited internally) Switching point 0 (unattenuated)≤ 0.15 mA 1 (attenuated)≥ 1.3 mA Signal delay< 1 ms (input/AS-Interface) Output Number/Type4 electronic outputs, NPN, overload proof and short-circuit proof Supplyfrom AS-Interface Voltage12 ... 31 V Current≤ 100 mA per output, ≤ 100 mA in total, including input supply Usage categoryDC-1 "general use" (ohmic and weak inductive loads in accordance with IEC 60947) Directive conformity Electromagnetic compatibility Directive 2014/30/EUEN 62026-2:2013 Standard conformity Degree of protectionEN 60529:2000 Fieldbus standardEN 62026-2:2013 Emitted interferenceEN 61000-6-4:2007 AS-InterfaceEN 62026-2:2013 Noise immunityEN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 Programming instructions ProfileS-7.A.7 IO code7 ID codeA ID1 code7 ID2 code7 Data bits (function via AS-Interface) input output D0 IN1 OUT1 D1 IN2 OUT2 D2 IN3 OUT3 D3 IN4 OUT4 Parameter bits (programmable via AS-i)function P0not used P1Input filterP1 = 0 input filter on, pulse suppression ≤ 2 msP1 = 1 input filter off (default settings) P2Synchronous modeP2 = 0 synchronous mode onP2 = 1 synchronous mode off (default settings) P3not used Approvals and certificates UL approvalProtection class IP20 is not included in the UL approval. The protection class is tested by Pepperl+Fuchs. Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-25 ... 85 °C (-13 ... 185 °F) Relative humidity85 % , noncondensing Climatic conditionsFor indoor use only Altitude≤ 5000 m above MSL Shock and impact resistance30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks Vibration resistance0.35 mm 10 ... 57 Hz , 5 g, 57 Hz ... 150 Hz, 10 cycles Pollution degree2 Mechanical specifications Degree of protectionIP20 according to EN 60529 Connection200 mm, PVC cable 0.5 mm2 Material HousingPolyamide hot-melt adhesive Mass33 g NoteThis device is maintenance-free. If the device is used in a manner not specified by the manufaturer, the protection provided by the device may be impaired. Classifications SystemClasscode ECLASS 11.027242604 ECLASS 10.0.127242604 ECLASS 9.027242604 ECLASS 8.027242604 ECLASS 5.127242604 ETIM 8.0EC001599 ETIM 7.0EC001599 ETIM 6.0EC001599 ETIM 5.0EC001599 UNSPSC 12.139121535 Datasheet excerpt: Technical data of  VBA-4E4A-CB10-ZEJ/E0J-FL Product Description Printed circuit board module4 inputs/4 outputs General specifications Node typeA/B node AS-Interface specificationV3.0 Required master specification≥ V3.0 UL File NumberE223772 MTBF267 a Indicators/operating means LED FAULTerror display; LED redred: communication error or address is 0red flashing: overload of outputs LED PWRAS-Interface voltage; green LEDgreen: voltage OKflashing green: address 0 LED INswitching state (input); 4 LED yellow LED OUTSwitching state (output); 4 LED yellow Electrical specifications Rated operating voltage26.5 ... 31.6 V from AS-Interface (PELV) Rated operating current≤ 40 mA (without inputs/outputs)/max. 160 mA Protection classIII Surge protectionUe: overvoltage category II, safe isolated power supplies (PELV) Input Number/Type4 inputs for mechanical contacts or 3-wire sensors (PNP), DC Supplyfrom AS-Interface Voltage12 ... 31 V Current loading capacity≤ 100 mA Total including output current, overload and short-circuit proof Input current≤ 4 mA (limited internally) Switching point 0 (unattenuated)≤ 0.15 mA 1 (attenuated)≥ 1.3 mA Signal delay< 1 ms (input/AS-Interface) Output Number/Type4 electronic outputs, NPN, overload proof and short-circuit proof Supplyfrom AS-Interface Voltage12 ... 31 V Current≤ 100 mA per output, ≤ 100 mA in total, including input supply Usage categoryDC-1 "general use" (ohmic and weak inductive loads in accordance with IEC 60947) Directive conformity Electromagnetic compatibility Directive 2014/30/EUEN 62026-2:2013 Standard conformity Degree of protectionEN 60529:2000 Fieldbus standardEN 62026-2:2013 Emitted interferenceEN 61000-6-4:2007 AS-InterfaceEN 62026-2:2013 Noise immunityEN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 Programming instructions ProfileS-7.A.7 IO code7 ID codeA ID1 code7 ID2 code7 Data bits (function via AS-Interface) input output D0 IN1 OUT1 D1 IN2 OUT2 D2 IN3 OUT3 D3 IN4 OUT4 Parameter bits (programmable via AS-i)function P0not used P1Input filterP1 = 0 input filter on, pulse suppression ≤ 2 msP1 = 1 input filter off (default settings) P2Synchronous modeP2 = 0 synchronous mode onP2 = 1 synchronous mode off (default settings) P3not used Approvals and certificates UL approvalProtection class IP20 is not included in the UL approval. The protection class is tested by Pepperl+Fuchs. Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-25 ... 85 °C (-13 ... 185 °F) Relative humidity85 % , noncondensing Climatic conditionsFor indoor use only Altitude≤ 5000 m above MSL Shock and impact resistance30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks Vibration resistance0.35 mm 10 ... 57 Hz , 5 g, 57 Hz ... 150 Hz, 10 cycles Pollution degree2 Mechanical specifications Degree of protectionIP20 according to EN 60529 Connection200 mm, PVC cable 0.5 mm2 Material HousingPolyamide hot-melt adhesive Mass33 g NoteThis device is maintenance-free. If the device is used in a manner not specified by the manufaturer, the protection provided by the device may be impaired. Classifications SystemClasscode ECLASS 11.027242604 ECLASS 10.0.127242604 ECLASS 9.027242604 ECLASS 8.027242604 ECLASS 5.127242604 ETIM 8.0EC001599 ETIM 7.0EC001599 ETIM 6.0EC001599 ETIM 5.0EC001599 UNSPSC 12.139121535