VAN-115/230AC-K16 PEPPERL+FUCHS - Part number: 129377

Datasheet excerpt: Technical data of  VAN-115/230AC-K16 Product Description AS-Interface power supply, data decoupling, 8 A General specifications UL File NumberE223176 MTBF100 a Indicators/operating means Reset push-button switchFUSE mode reset Power selection switchchangeover switch for 115 V AC/230 V AC LED Overloadred LED, flashes in the FUSE mode LED IR onred LED:ON: Plug-in jumper position 2-3OFF: Plug-in jumper position 1-2 Plug-in jumperPosition 1-2: Communication ModePosition 2-3: IR addressing LED AS-i okoperating display; LED green Electrical specifications FusingT8A/250 V AC HBC (not accessible) Capacity factor> 0.5 Rated operating voltagenominal: 100 ... 120 V AC/220 ... 240 V AC (front end selectable)permissible: 85 ... 132 V AC/184 ... 264 V AC/230 ... 375 V DC Rated operating current6,0 A (Switch position 115 V)2.8 A (Switch position 230 V) Supply frequency47 ... 63 Hz or DC Efficiencytyp. 92 % (at 230 V AC/8 A) Surge protectionlimited to max. 55 V Output Short-circuit protection/overloadFUSE Mode (2 ... 5 s current, then trips) Current limit> 8.4 A Voltage30.55 V DC ± 3 % Current8 A Galvanic isolationovervoltage category III Residual ripple≤ 50 mVss (500 kHz bandwidth, 50-Ω-measurement with ohmic load) Short-circuit current12 ... 25 A (max. 5 s) Standard conformity Electromagnetic compatibilityemitted interference in accordance with EN 50081-2 class B (EN 55011, EN 55022)noise immunity in accordance with EN 61000-6-2, EN 61000-4-2 to EN 61000-4-6, EN 61000-4-11 Ambient conditions Ambient temperature-10 ... 70 °C (14 ... 158 °F) (Measured 25 mm below the device)from 60° C 6W/°C power recovery necessary Storage temperature-25 ... 85 °C (-13 ... 185 °F) Pollution degree2 Mechanical specifications Degree of protectionIP20 according to EN 60529 Protection class1 (IEC 60536); Protective conductor connection necessary ConnectionConnection terminals, max. conductor cross-section flexible: 0.5 ... 4 mm2fixed: 0.5 ... 6 mm2stripped length 7 mm, connector sleeves are permissible Material Housingmetal Mass890 g Classifications SystemClasscode ECLASS 11.027040301 ECLASS 10.0.127040301 ECLASS 9.027040301 ECLASS 8.027040301 ECLASS 5.127040301 ETIM 8.0EC002540 ETIM 7.0EC002540 ETIM 6.0EC002540 ETIM 5.0EC002540 UNSPSC 12.139121004 Datasheet excerpt: Technical data of  VAN-115/230AC-K16 Product Description AS-Interface power supply, data decoupling, 8 A General specifications UL File NumberE223176 MTBF100 a Indicators/operating means Reset push-button switchFUSE mode reset Power selection switchchangeover switch for 115 V AC/230 V AC LED Overloadred LED, flashes in the FUSE mode LED IR onred LED:ON: Plug-in jumper position 2-3OFF: Plug-in jumper position 1-2 Plug-in jumperPosition 1-2: Communication ModePosition 2-3: IR addressing LED AS-i okoperating display; LED green Electrical specifications FusingT8A/250 V AC HBC (not accessible) Capacity factor> 0.5 Rated operating voltagenominal: 100 ... 120 V AC/220 ... 240 V AC (front end selectable)permissible: 85 ... 132 V AC/184 ... 264 V AC/230 ... 375 V DC Rated operating current6,0 A (Switch position 115 V)2.8 A (Switch position 230 V) Supply frequency47 ... 63 Hz or DC Efficiencytyp. 92 % (at 230 V AC/8 A) Surge protectionlimited to max. 55 V Output Short-circuit protection/overloadFUSE Mode (2 ... 5 s current, then trips) Current limit> 8.4 A Voltage30.55 V DC ± 3 % Current8 A Galvanic isolationovervoltage category III Residual ripple≤ 50 mVss (500 kHz bandwidth, 50-Ω-measurement with ohmic load) Short-circuit current12 ... 25 A (max. 5 s) Standard conformity Electromagnetic compatibilityemitted interference in accordance with EN 50081-2 class B (EN 55011, EN 55022)noise immunity in accordance with EN 61000-6-2, EN 61000-4-2 to EN 61000-4-6, EN 61000-4-11 Ambient conditions Ambient temperature-10 ... 70 °C (14 ... 158 °F) (Measured 25 mm below the device)from 60° C 6W/°C power recovery necessary Storage temperature-25 ... 85 °C (-13 ... 185 °F) Pollution degree2 Mechanical specifications Degree of protectionIP20 according to EN 60529 Protection class1 (IEC 60536); Protective conductor connection necessary ConnectionConnection terminals, max. conductor cross-section flexible: 0.5 ... 4 mm2fixed: 0.5 ... 6 mm2stripped length 7 mm, connector sleeves are permissible Material Housingmetal Mass890 g Classifications SystemClasscode ECLASS 11.027040301 ECLASS 10.0.127040301 ECLASS 9.027040301 ECLASS 8.027040301 ECLASS 5.127040301 ETIM 8.0EC002540 ETIM 7.0EC002540 ETIM 6.0EC002540 ETIM 5.0EC002540 UNSPSC 12.139121004