UC2000-L2M-E7-T-2M PEPPERL+FUCHS - Part number: 299134

Datasheet excerpt: Technical data of  UC2000-L2M-E7-T-2M Product Description Single head system General specifications Sensing range60 ... 2000 mm Adjustment range80 ... 2000 mm Dead band0 ... 60 mm Standard target plate100 mm x 100 mm Transducer frequency175 kHz Nominal ratings Response delayminimum: 60 ms factory setting: 120 ms Time delay before availability≤ 1600 ms Indicators/operating means LED greenOperating display LED yellow 1switching state switch output 1 LED yellow 2switching state switch output 2 LED rederror Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 50 mA Interface Interface typeSerial interface (programming adapter required) 9600 BPS, no parity, 8 data bits, 1 stop bit Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level4 V ... UB Input impedance> 12 kΩ Output rated operating current< 12 mA Pulse length0.5 ... 300 ms (level 1) Pulse interval≥ 33 ms (level 0) Synchronization frequency Common mode operation≤ 30 Hz Multiplex operation≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ) Output Output type2 switch outputs NPN, NO/NC, programmable Rated operating current200 mA , short-circuit/overload protected Voltage drop≤ 2 V Repeat accuracy≤ 0.1 % of full-scale value Switching frequency≤ 5 Hz Range hysteresisprogrammable , preset to 1 mm Temperature influence< 1.5 % of full-scale value Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 Approvals and certificates EAC conformityTR CU 020/2011 TR CU 037/2016 UL approvalcULus Listed, General Purpose CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-40 ... 70 °C (-40 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typecable , 5-pin Degree of protectionIP67 Material HousingPA-GF35 CablePUR Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Cable Sheath diameter7.25 mm Bending radius> 37.3 mm , fixed > 74.7 mm , moving Core cross-section5 x 0.82 mm2 Length2 m Mass345 g Factory settings Output 1near switch point: 80 mm far switch point: 2000 mm Output mode: Window mode output behavior: NO contact Output 2near switch point: 150 mm far switch point: 1000 mm Output mode: Window mode output behavior: NO contact Beam widthwide Evaluation procedureaveraging (MxN)M = 5N = 2 General information Supplementary informationSwitch settings of the external programming adapter: "output load": pull-up "output logic": inv Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960 Datasheet excerpt: Technical data of  UC2000-L2M-E7-T-2M Product Description Single head system General specifications Sensing range60 ... 2000 mm Adjustment range80 ... 2000 mm Dead band0 ... 60 mm Standard target plate100 mm x 100 mm Transducer frequency175 kHz Nominal ratings Response delayminimum: 60 ms factory setting: 120 ms Time delay before availability≤ 1600 ms Indicators/operating means LED greenOperating display LED yellow 1switching state switch output 1 LED yellow 2switching state switch output 2 LED rederror Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 50 mA Interface Interface typeSerial interface (programming adapter required) 9600 BPS, no parity, 8 data bits, 1 stop bit Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level4 V ... UB Input impedance> 12 kΩ Output rated operating current< 12 mA Pulse length0.5 ... 300 ms (level 1) Pulse interval≥ 33 ms (level 0) Synchronization frequency Common mode operation≤ 30 Hz Multiplex operation≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 ) Output Output type2 switch outputs NPN, NO/NC, programmable Rated operating current200 mA , short-circuit/overload protected Voltage drop≤ 2 V Repeat accuracy≤ 0.1 % of full-scale value Switching frequency≤ 5 Hz Range hysteresisprogrammable , preset to 1 mm Temperature influence< 1.5 % of full-scale value Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 Approvals and certificates EAC conformityTR CU 020/2011 TR CU 037/2016 UL approvalcULus Listed, General Purpose CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-40 ... 70 °C (-40 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typecable , 5-pin Degree of protectionIP67 Material HousingPA-GF35 CablePUR Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Cable Sheath diameter7.25 mm Bending radius> 37.3 mm , fixed > 74.7 mm , moving Core cross-section5 x 0.82 mm2 Length2 m Mass345 g Factory settings Output 1near switch point: 80 mm far switch point: 2000 mm Output mode: Window mode output behavior: NO contact Output 2near switch point: 150 mm far switch point: 1000 mm Output mode: Window mode output behavior: NO contact Beam widthwide Evaluation procedureaveraging (MxN)M = 5N = 2 General information Supplementary informationSwitch settings of the external programming adapter: "output load": pull-up "output logic": inv Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960