UCC2500-50GK-B26-8MOL PEPPERL+FUCHS - Part number: 312896

Datasheet excerpt: Technical data of  UCC2500-50GK-B26-8MOL Product Description Single head system General specifications Sensing range150 ... 2500 mm Dead band0 ... 150 mm Standard target plate100 mm x 100 mm Transducer frequency120 kHz Electrical specifications Operating voltagefor UART and PWM operation: UUART/PWM = 2.5 ... 5 V DC, typical 3.3 V for LIN operation: ULIN = 8 ... 18 V DC, typical 12 V No-load supply current≤ 60 mA at 3.3 V DC ≤ 20 mA at 12 V DC Quiescent current indication< 3 µA during standby mode at UART- and PWM operation Power consumption≤ 250 mW in the measurement operating mode Time delay before availability≤ 70 ms Interface 1 Interface typePhysical LIN interface Transfer rate19.2 kBit/s (8N1) Cycle time55 ms Resolution10 mm (corresponding to 1 LSB) Interface 2 Interface typeUART 3.3V Transfer rate19.2 kBit/s (8N1) Cycle time55 ms Resolution10 mm (corresponding to 1 LSB) Input Input typeStandby active Signal levellow: 0 ... 0.8 V Output Output typePWM output (PNP) , not short-circuit protected Resolutionpulse length 10 µs /cm Output rated operating currentmax. 10 mA Temperature influence3 % of full-scale value over the entire temperature range Directive conformity Electromagnetic compatibility Directive 2014/30/EUEN 60947-5-2:2007+A1:2012 : chapter 8.6.2.1, 8.6.2.2, 8.6.3 The sensor is designed to be supplied by a battery. The sensor signals are further processed in a control unit, which is also responsible for EMC protection. Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typefixed cable with plug Degree of protectionIP66 / IP67 ( connector excluded ) Material HousingPBT Transducerepoxy resin/hollow glass bead mixture; Polyurethane foam, PTFE coated ConnectorMolex connector 70107-0007 Number of pins8 Cable Length276 mm ± 20 mm Mass100 g Factory settings OutputPWM output (PNP) Temperature compensation Address setting 7 Beam widthwide General information Scope of delivery2 nuts plastic Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960 Datasheet excerpt: Technical data of  UCC2500-50GK-B26-8MOL Product Description Single head system General specifications Sensing range150 ... 2500 mm Dead band0 ... 150 mm Standard target plate100 mm x 100 mm Transducer frequency120 kHz Electrical specifications Operating voltagefor UART and PWM operation: UUART/PWM = 2.5 ... 5 V DC, typical 3.3 V for LIN operation: ULIN = 8 ... 18 V DC, typical 12 V No-load supply current≤ 60 mA at 3.3 V DC ≤ 20 mA at 12 V DC Quiescent current indication< 3 µA during standby mode at UART- and PWM operation Power consumption≤ 250 mW in the measurement operating mode Time delay before availability≤ 70 ms Interface 1 Interface typePhysical LIN interface Transfer rate19.2 kBit/s (8N1) Cycle time55 ms Resolution10 mm (corresponding to 1 LSB) Interface 2 Interface typeUART 3.3V Transfer rate19.2 kBit/s (8N1) Cycle time55 ms Resolution10 mm (corresponding to 1 LSB) Input Input typeStandby active Signal levellow: 0 ... 0.8 V Output Output typePWM output (PNP) , not short-circuit protected Resolutionpulse length 10 µs /cm Output rated operating currentmax. 10 mA Temperature influence3 % of full-scale value over the entire temperature range Directive conformity Electromagnetic compatibility Directive 2014/30/EUEN 60947-5-2:2007+A1:2012 : chapter 8.6.2.1, 8.6.2.2, 8.6.3 The sensor is designed to be supplied by a battery. The sensor signals are further processed in a control unit, which is also responsible for EMC protection. Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typefixed cable with plug Degree of protectionIP66 / IP67 ( connector excluded ) Material HousingPBT Transducerepoxy resin/hollow glass bead mixture; Polyurethane foam, PTFE coated ConnectorMolex connector 70107-0007 Number of pins8 Cable Length276 mm ± 20 mm Mass100 g Factory settings OutputPWM output (PNP) Temperature compensation Address setting 7 Beam widthwide General information Scope of delivery2 nuts plastic Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960