RL28-55-LAS/76a/82b/105/110 PEPPERL+FUCHS - Part number: 123758

Datasheet excerpt: Technical data of  RL28-55-LAS/76a/82b/105/110 Product Description Retroreflective sensor with polarization filter General specifications Effective detection range0 ... 30 m Reflector distance0.3 ... 30 m Threshold detection range42 m Reference targetMH82 reflector Light sourcelaser diode Light typemodulated visible red light Polarization filteryes Laser nominal ratings NoteLASER LIGHT , DO NOT STARE INTO BEAM Laser class1 Wave length650 nm Beam divergence< 1.5 mrad Pulse length4.5 µs Repetition rate6 kHz ... 20 kHz max. pulse energy4 nJ Diameter of the light spot45 mm at 30 m Opening angleEmitter: < 0.1 ° Receiver: < 2 ° Ambient light limit50000 Lux Functional safety related parameters MTTFd560 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Operation indicatorLED green Function indicator2 LEDs yellow, light up when light beam is free, flash when falling short of the stability control, off when light beam is interrupted Control elementssensitivity adjustment (Adjustment to < 25% of the effective operating range) , Light-on/dark-on changeover switch Electrical specifications Operating voltage10 ... 30 V DC Ripplemax. 10 % No-load supply current≤ 35 mA Protection classII, rated insulation voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1 Input Test inputemitter deactivation with +Ub Output Pre-fault indication output1 PNP, inactive when falling short of the stability control for 10;simmediately inactive if 4 light beam interruptions take place Switching typelight/dark on switchable Signal output1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Switching voltagemax. 30 V DC Switching currentmax. 100 mA Voltage drop≤ 2.5 V DC Switching frequency1000 Hz Response time0.5 ms Conformity Product standardEN 60947-5-2 Laser safetyEN 60825-1 Approvals and certificates EAC conformityTR CU 020/2011 Protection classII, rated voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1 UL approvalE87056 , cULus Listed , class 2 power supply , type rating 1 FDA approvalIEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 Ambient conditions Ambient temperature-10 ... 50 °C (14 ... 122 °F) Storage temperature-20 ... 75 °C (-4 ... 167 °F) Mechanical specifications Housing width25.8 mm Housing height88 mm Housing depth54.3 mm Degree of protectionIP67 Connection5-pin, M12 x 1 plastic connector Material HousingPlastic ABS Optical facePlastic pane Mass80 g Classifications SystemClasscode ECLASS 11.027270902 ECLASS 10.0.127270902 ECLASS 9.027270902 ECLASS 8.027270902 ECLASS 5.127270902 ETIM 8.0EC002717 ETIM 7.0EC002717 ETIM 6.0EC002717 ETIM 5.0EC002717 UNSPSC 12.139121528 Datasheet excerpt: Technical data of  RL28-55-LAS/76a/82b/105/110 Product Description Retroreflective sensor with polarization filter General specifications Effective detection range0 ... 30 m Reflector distance0.3 ... 30 m Threshold detection range42 m Reference targetMH82 reflector Light sourcelaser diode Light typemodulated visible red light Polarization filteryes Laser nominal ratings NoteLASER LIGHT , DO NOT STARE INTO BEAM Laser class1 Wave length650 nm Beam divergence< 1.5 mrad Pulse length4.5 µs Repetition rate6 kHz ... 20 kHz max. pulse energy4 nJ Diameter of the light spot45 mm at 30 m Opening angleEmitter: < 0.1 ° Receiver: < 2 ° Ambient light limit50000 Lux Functional safety related parameters MTTFd560 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Operation indicatorLED green Function indicator2 LEDs yellow, light up when light beam is free, flash when falling short of the stability control, off when light beam is interrupted Control elementssensitivity adjustment (Adjustment to < 25% of the effective operating range) , Light-on/dark-on changeover switch Electrical specifications Operating voltage10 ... 30 V DC Ripplemax. 10 % No-load supply current≤ 35 mA Protection classII, rated insulation voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1 Input Test inputemitter deactivation with +Ub Output Pre-fault indication output1 PNP, inactive when falling short of the stability control for 10;simmediately inactive if 4 light beam interruptions take place Switching typelight/dark on switchable Signal output1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Switching voltagemax. 30 V DC Switching currentmax. 100 mA Voltage drop≤ 2.5 V DC Switching frequency1000 Hz Response time0.5 ms Conformity Product standardEN 60947-5-2 Laser safetyEN 60825-1 Approvals and certificates EAC conformityTR CU 020/2011 Protection classII, rated voltage ≤ 250 V AC with pollution degree 1-2 according to IEC 60664-1 UL approvalE87056 , cULus Listed , class 2 power supply , type rating 1 FDA approvalIEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 Ambient conditions Ambient temperature-10 ... 50 °C (14 ... 122 °F) Storage temperature-20 ... 75 °C (-4 ... 167 °F) Mechanical specifications Housing width25.8 mm Housing height88 mm Housing depth54.3 mm Degree of protectionIP67 Connection5-pin, M12 x 1 plastic connector Material HousingPlastic ABS Optical facePlastic pane Mass80 g Classifications SystemClasscode ECLASS 11.027270902 ECLASS 10.0.127270902 ECLASS 9.027270902 ECLASS 8.027270902 ECLASS 5.127270902 ETIM 8.0EC002717 ETIM 7.0EC002717 ETIM 6.0EC002717 ETIM 5.0EC002717 UNSPSC 12.139121528