DK10-LAS/9S20 PEPPERL+FUCHS - Part number: 418070

Datasheet excerpt: Technical data of  DK10-LAS/9S20 Product Description Print mark contrast sensor, 300 mm detection range, red laser light, laser class 2, light/dark on, sensitivity adjuster, push-pull output, emitter switch-off, timer function, M12 plug General specifications Sensor range300 mm Detection range3 ... 300 mm Light sourcelaser diode Light typemodulated visible red light Laser nominal ratings NoteLASER LIGHT , DO NOT STARE INTO BEAM Laser class2 Wave length650 nm Beam divergence< 1.5 mrad Pulse length1.5 µs Repetition rate108.7 kHz max. pulse energy2.1 nJ Light spot representation0.8 mm at a distance of 300 mm Ambient light limit Continuous light40000 Lux Functional safety related parameters MTTFd550 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Function indicatorLED yellow: lights up if receiver is lit (light on), lights up if receiver is not lit (dark on) Control elementsLight-on/dark-on changeover switch, sensitivity adjuster Electrical specifications Operating voltage10 ... 30 V DC Ripple10 % No-load supply current≤ 55 mA Input Test inputemitter deactivation with +Ub Output Switching typelight/dark on switchable Signal outputPush-pull output, short-circuit protected, reverse polarity protected Switching voltagePNP: UB - 2.5 V / NPN: URest 1.5 V Switching currentmax. 200 mA Switching frequency16.5 kHz Response time30 µs Timer functionrising edge , mono stable Pulse length20 ms Conformity Product standardEN 60947-5-2 Laser safetyIEC 60825-1:2007 Compliance with standards and directives Standard conformity Shock and impact resistanceIEC / EN 60068. half-sine, 40 g in each X, Y and Z directions Vibration resistanceIEC / EN 60068-2-6. Sinus. 10 -150 Hz, 5 g in each X, Y and Z directions Approvals and certificates EAC conformityTR CU 020/2011 UL approvalcULus Listed , Class 2 power source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-10 ... 50 °C (14 ... 122 °F) Storage temperature-20 ... 75 °C (-4 ... 167 °F) Mechanical specifications Housing width33 mm Housing height85.6 mm Housing depth60.8 mm Degree of protectionIP67 Connection5-pin, M12 x 1 connector Material HousingPC (glass-fiber-reinforced Makrolon) Optical faceglass Mass200 g Classifications SystemClasscode ECLASS 11.027270906 ECLASS 10.0.127270906 ECLASS 9.027270906 ECLASS 8.027270906 ECLASS 5.127270906 ETIM 8.0EC001820 ETIM 7.0EC001820 ETIM 6.0EC001820 ETIM 5.0EC001820 UNSPSC 12.139121528 Datasheet excerpt: Technical data of  DK10-LAS/9S20 Product Description Print mark contrast sensor, 300 mm detection range, red laser light, laser class 2, light/dark on, sensitivity adjuster, push-pull output, emitter switch-off, timer function, M12 plug General specifications Sensor range300 mm Detection range3 ... 300 mm Light sourcelaser diode Light typemodulated visible red light Laser nominal ratings NoteLASER LIGHT , DO NOT STARE INTO BEAM Laser class2 Wave length650 nm Beam divergence< 1.5 mrad Pulse length1.5 µs Repetition rate108.7 kHz max. pulse energy2.1 nJ Light spot representation0.8 mm at a distance of 300 mm Ambient light limit Continuous light40000 Lux Functional safety related parameters MTTFd550 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Function indicatorLED yellow: lights up if receiver is lit (light on), lights up if receiver is not lit (dark on) Control elementsLight-on/dark-on changeover switch, sensitivity adjuster Electrical specifications Operating voltage10 ... 30 V DC Ripple10 % No-load supply current≤ 55 mA Input Test inputemitter deactivation with +Ub Output Switching typelight/dark on switchable Signal outputPush-pull output, short-circuit protected, reverse polarity protected Switching voltagePNP: UB - 2.5 V / NPN: URest 1.5 V Switching currentmax. 200 mA Switching frequency16.5 kHz Response time30 µs Timer functionrising edge , mono stable Pulse length20 ms Conformity Product standardEN 60947-5-2 Laser safetyIEC 60825-1:2007 Compliance with standards and directives Standard conformity Shock and impact resistanceIEC / EN 60068. half-sine, 40 g in each X, Y and Z directions Vibration resistanceIEC / EN 60068-2-6. Sinus. 10 -150 Hz, 5 g in each X, Y and Z directions Approvals and certificates EAC conformityTR CU 020/2011 UL approvalcULus Listed , Class 2 power source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-10 ... 50 °C (14 ... 122 °F) Storage temperature-20 ... 75 °C (-4 ... 167 °F) Mechanical specifications Housing width33 mm Housing height85.6 mm Housing depth60.8 mm Degree of protectionIP67 Connection5-pin, M12 x 1 connector Material HousingPC (glass-fiber-reinforced Makrolon) Optical faceglass Mass200 g Classifications SystemClasscode ECLASS 11.027270906 ECLASS 10.0.127270906 ECLASS 9.027270906 ECLASS 8.027270906 ECLASS 5.127270906 ETIM 8.0EC001820 ETIM 7.0EC001820 ETIM 6.0EC001820 ETIM 5.0EC001820 UNSPSC 12.139121528