LGM25-2000-IO/110/115b PEPPERL+FUCHS - Part number: 251333-0020

Datasheet excerpt: Technical data of  LGM25 Product Description Measuring automation light grid with beam spacing of 25 mm, IO-Link interface, push-pull output, fixed cable with M12 plug General specifications Effective detection rangeStandard : 0.3 ... 6 m Threshold detection range7.5 m Light sourceIRED Light typemodulated infrared light , 850 nm Field heightsee Table 1, max. 3200 mm Beam crossoverFactory setting: three beam crossing, deactivateable Beam blankingadjustable max. 2 fixed suppressible beam areas (blanking) Beam spacing25 mm Number of beamssee Table 1, max. 129 Operating modeEmitter: Emitter power adjustable in two ranges Optical resolutionwithout beam crossover: 25 mm with beam crossover: 12.5 mm with in 25%  and  75% of the range Opening angle10 ° Ambient light limit> 50000 Lux (if external light source is outside the opening angle) Functional safety related parameters MTTFd34 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Operation indicatorLED green:constantly on - power-ondouble pulse flashing (0.8 Hz) - undervoltageflashing (4 Hz) - short circuitflashing with short interruptions (1 Hz) - IO-Link mode Status indicatorEmitter: LED yellow constantly on - high emitter power constantly off - low emitter power flashing (8 Hz) - error message Receiver: LED yellow: constantly on - object detected constantly off - no object detected flashing (4 Hz) - below stability control limit flashing (8 Hz) - error message Control elementsReceiver: 2 touch buttons for programming Electrical specifications Operating voltage18 ... 30 V DC Ripple10 % No-load supply currentEmitter ≤: 50 mA Receiver: ≤ 150 mA (without outputs) Time delay before availabilitysee Table 1, max. 2.3 s Interface Interface typeIO-Link ( pin 4 ) IO-Link revision1.0 Device ID1050369 ... 1050400 ( 0x100701 ... 0x100720 ) COM-ModeCOM2 (38.4 kBit/s) Min. cycle time2.3 ms Process data width16 bit SIO mode supportyes Input Test inputEmitter switch-off with +UB or 0 V at pin 4 (emitter) Function inputRange input activation from 1.6 m with +UB or 0 V on pin 2 (emitter) Teach-In input for parameterization on pin 8 (receiver) Output Pre-fault indication outputStability Control (SC) 1 PNP, short-circuit protected, reverse polarity protected on pin 2 (receiver) Switching typeFactory setting: dark on , Switchable to light-on mode Signal outputCommand interface: Pin 4 IO-Link interface C or used as switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver)Switch output: Pin 5 switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver) synchronized with pin 4 Switching thresholdFactory setting: The signal tracking for the threshold value is deactivated, increasing the optical resolution by a maximum of 4 mm; switchable to active signal tracking Switching voltagemax. 30 V DC Switching currentmax. 100 mA Voltage drop≤ 2 V DC Switching frequencysee Table 1, max. 135 Hz Response timesee Table 1, max. 12 ms Timer functionOff-delay programmable from 0 ... 1.25 s in 5 ms steps (adjustment via IO-Link only) Conformity Communication interfaceIEC 61131-9 Product standardEN 60947-5-2 Approvals and certificates Protection classIII ( IEC 61140 ) UL approvalcULus Listed CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-30 ... 60 °C (-22 ... 140 °F) Storage temperature-30 ... 70 °C (-22 ... 158 °F) Mechanical specifications Conductor cross sectionmin. 0.25 mm2 Housing width20 mm Housing depth30.5 mm Housing length Lsee Table 1, max. 3360 mm Degree of protectionIP67 ConnectionEmitter: connecting cable with 4-pin, M12 x 1 connector , 330 mm total length Receiver: connecting cable with 8-pin, M12 x 1 connector , 350 mm total length Material Housingextruded aluminum section , Silver anodized Optical facePlastic pane , Polycarbonate Masssee Table 1, max. 1750 g (per profile) Cable lengthmax. 30 m Classifications SystemClasscode ECLASS 11.027270910 ECLASS 10.0.127270910 ECLASS 9.027270910 ECLASS 8.027270910 ECLASS 5.127270910 ETIM 8.0EC002549 ETIM 7.0EC002549 ETIM 6.0EC002549 ETIM 5.0EC002549 UNSPSC 12.139121528 Datasheet excerpt: Technical data of  LGM25 Product Description Measuring automation light grid with beam spacing of 25 mm, IO-Link interface, push-pull output, fixed cable with M12 plug General specifications Effective detection rangeStandard : 0.3 ... 6 m Threshold detection range7.5 m Light sourceIRED Light typemodulated infrared light , 850 nm Field heightsee Table 1, max. 3200 mm Beam crossoverFactory setting: three beam crossing, deactivateable Beam blankingadjustable max. 2 fixed suppressible beam areas (blanking) Beam spacing25 mm Number of beamssee Table 1, max. 129 Operating modeEmitter: Emitter power adjustable in two ranges Optical resolutionwithout beam crossover: 25 mm with beam crossover: 12.5 mm with in 25%  and  75% of the range Opening angle10 ° Ambient light limit> 50000 Lux (if external light source is outside the opening angle) Functional safety related parameters MTTFd34 a Mission Time (TM)20 a Diagnostic Coverage (DC)60 % Indicators/operating means Operation indicatorLED green:constantly on - power-ondouble pulse flashing (0.8 Hz) - undervoltageflashing (4 Hz) - short circuitflashing with short interruptions (1 Hz) - IO-Link mode Status indicatorEmitter: LED yellow constantly on - high emitter power constantly off - low emitter power flashing (8 Hz) - error message Receiver: LED yellow: constantly on - object detected constantly off - no object detected flashing (4 Hz) - below stability control limit flashing (8 Hz) - error message Control elementsReceiver: 2 touch buttons for programming Electrical specifications Operating voltage18 ... 30 V DC Ripple10 % No-load supply currentEmitter ≤: 50 mA Receiver: ≤ 150 mA (without outputs) Time delay before availabilitysee Table 1, max. 2.3 s Interface Interface typeIO-Link ( pin 4 ) IO-Link revision1.0 Device ID1050369 ... 1050400 ( 0x100701 ... 0x100720 ) COM-ModeCOM2 (38.4 kBit/s) Min. cycle time2.3 ms Process data width16 bit SIO mode supportyes Input Test inputEmitter switch-off with +UB or 0 V at pin 4 (emitter) Function inputRange input activation from 1.6 m with +UB or 0 V on pin 2 (emitter) Teach-In input for parameterization on pin 8 (receiver) Output Pre-fault indication outputStability Control (SC) 1 PNP, short-circuit protected, reverse polarity protected on pin 2 (receiver) Switching typeFactory setting: dark on , Switchable to light-on mode Signal outputCommand interface: Pin 4 IO-Link interface C or used as switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver)Switch output: Pin 5 switching output Q; 1 short-circuit proof reverse polarity protected push-pull output (receiver) synchronized with pin 4 Switching thresholdFactory setting: The signal tracking for the threshold value is deactivated, increasing the optical resolution by a maximum of 4 mm; switchable to active signal tracking Switching voltagemax. 30 V DC Switching currentmax. 100 mA Voltage drop≤ 2 V DC Switching frequencysee Table 1, max. 135 Hz Response timesee Table 1, max. 12 ms Timer functionOff-delay programmable from 0 ... 1.25 s in 5 ms steps (adjustment via IO-Link only) Conformity Communication interfaceIEC 61131-9 Product standardEN 60947-5-2 Approvals and certificates Protection classIII ( IEC 61140 ) UL approvalcULus Listed CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-30 ... 60 °C (-22 ... 140 °F) Storage temperature-30 ... 70 °C (-22 ... 158 °F) Mechanical specifications Conductor cross sectionmin. 0.25 mm2 Housing width20 mm Housing depth30.5 mm Housing length Lsee Table 1, max. 3360 mm Degree of protectionIP67 ConnectionEmitter: connecting cable with 4-pin, M12 x 1 connector , 330 mm total length Receiver: connecting cable with 8-pin, M12 x 1 connector , 350 mm total length Material Housingextruded aluminum section , Silver anodized Optical facePlastic pane , Polycarbonate Masssee Table 1, max. 1750 g (per profile) Cable lengthmax. 30 m Classifications SystemClasscode ECLASS 11.027270910 ECLASS 10.0.127270910 ECLASS 9.027270910 ECLASS 8.027270910 ECLASS 5.127270910 ETIM 8.0EC002549 ETIM 7.0EC002549 ETIM 6.0EC002549 ETIM 5.0EC002549 UNSPSC 12.139121528