UC1000-18GS-2EP-IO-V15 PEPPERL+FUCHS - Part number: 304928-100002

Datasheet excerpt: Technical data of  UC1000-18GS-2EP-IO-V15 Product Description Single head system General specifications Sensing range70 ... 1000 mm Adjustment range90 ... 1000 mm Dead band0 ... 70 mm Standard target plate100 mm x 100 mm Transducer frequency255 kHz Response delayminimum : 28 ms factory setting: 56 ms Sensor cycle time≥ 14 ms (factory setting) ; programmable to 60 s Temperature influencewith temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K Memory Non-volatile memoryEEPROM Write cycles300000 Indicators/operating means LED greensolid: power onflashing: standby mode or IO-Link communication LED yellowsolid: object in evaluation rangeflashing: switch point programming, object detected LED redsolid: errorflashing: switch point programming, object not detected Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 50 mA Power consumption≤ 700 mW Time delay before availability≤ 300 ms Interface 1 Interface typeIO-Link (via C/Q = Pin 4) IO-Link revision1.1 Device profileSmart Sensor Profile 2 Process data width32 bit Device ID0x300603 (3147267) Transfer rateCOM2 (38.4 kBit/s) Min. cycle time3 ms SIO mode supportyes Compatible master port typeClass A Class B (use 3-pole adapter or 3-wire cable) Interface 2 Interface typeIrDA (Infrared-Interface) Modepoint-to-point connection Transfer rate115.2 kBit/s Maximum communication distance5 cm Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level2.5 V ... UB Input impedance> 22 kΩ Output rated operating currentcurrent source < 2.5 mA Pulse length≥ 1 ms with external control, low active Synchronization frequency Common mode operation≤ 71 Hz Multiplex operation≤ 71 Hz / n , n = number of sensors , n ≤ 10 Switching output Output type2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected Rated operating current100 mA , short-circuit/overload protected Switching frequencyfactory setting: 10 Hz programmable to 23 Hz Voltage drop≤ 2.5 V Repeat accuracy≤ ± 0.1 % of full-scale value Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm Off-state current≤ 100 µA Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 IEC 61131-9:2013 Approvals and certificates EAC conformityTR CU 020/2011 TR CU 037/2016 UL approvalcULus Listed, Class 2 Power Source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typeConnector plug M12 x 1 , 5-pin Degree of protectionIP67 Material Housingstainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Installation positionany position Mass45 g Tightening torque, fastening screwsmax. 30 Nm Factory settings Output 1near switch point: 90 mm far switch point: 1000 mm output function: Window mode output behavior: NO contact Output 2near switch point: 90 mm far switch point: 500 mm output function: Window mode output behavior: NO contact Beam widthwide Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960 Datasheet excerpt: Technical data of  UC1000-18GS-2EP-IO-V15 Product Description Single head system General specifications Sensing range70 ... 1000 mm Adjustment range90 ... 1000 mm Dead band0 ... 70 mm Standard target plate100 mm x 100 mm Transducer frequency255 kHz Response delayminimum : 28 ms factory setting: 56 ms Sensor cycle time≥ 14 ms (factory setting) ; programmable to 60 s Temperature influencewith temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K Memory Non-volatile memoryEEPROM Write cycles300000 Indicators/operating means LED greensolid: power onflashing: standby mode or IO-Link communication LED yellowsolid: object in evaluation rangeflashing: switch point programming, object detected LED redsolid: errorflashing: switch point programming, object not detected Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 50 mA Power consumption≤ 700 mW Time delay before availability≤ 300 ms Interface 1 Interface typeIO-Link (via C/Q = Pin 4) IO-Link revision1.1 Device profileSmart Sensor Profile 2 Process data width32 bit Device ID0x300603 (3147267) Transfer rateCOM2 (38.4 kBit/s) Min. cycle time3 ms SIO mode supportyes Compatible master port typeClass A Class B (use 3-pole adapter or 3-wire cable) Interface 2 Interface typeIrDA (Infrared-Interface) Modepoint-to-point connection Transfer rate115.2 kBit/s Maximum communication distance5 cm Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level2.5 V ... UB Input impedance> 22 kΩ Output rated operating currentcurrent source < 2.5 mA Pulse length≥ 1 ms with external control, low active Synchronization frequency Common mode operation≤ 71 Hz Multiplex operation≤ 71 Hz / n , n = number of sensors , n ≤ 10 Switching output Output type2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected Rated operating current100 mA , short-circuit/overload protected Switching frequencyfactory setting: 10 Hz programmable to 23 Hz Voltage drop≤ 2.5 V Repeat accuracy≤ ± 0.1 % of full-scale value Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm Off-state current≤ 100 µA Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 IEC 61131-9:2013 Approvals and certificates EAC conformityTR CU 020/2011 TR CU 037/2016 UL approvalcULus Listed, Class 2 Power Source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typeConnector plug M12 x 1 , 5-pin Degree of protectionIP67 Material Housingstainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Installation positionany position Mass45 g Tightening torque, fastening screwsmax. 30 Nm Factory settings Output 1near switch point: 90 mm far switch point: 1000 mm output function: Window mode output behavior: NO contact Output 2near switch point: 90 mm far switch point: 500 mm output function: Window mode output behavior: NO contact Beam widthwide Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960