UC250-F77-EP-IO-V31 PEPPERL+FUCHS - Part number: 261242

Datasheet excerpt: Technical data of  UC250-F77-EP-IO-V31 Product Description Single head system General specifications Sensing range20 ... 250 mm Adjustment range25 ... 250 mm Dead band0 ... 20 mm Standard target plate10 mm x 10 mm Transducer frequency400 kHz Response delayminimum : 8 ms factory setting: 29 ms Sensor cycle time≥ 8 ms (factory setting) ; programmable to 60 s Memory Non-volatile memoryEEPROM Write cycles300000 Indicators/operating means LED greensolid: Power onflashing: Standby mode or IO-Link communication LED yellowsolid: object in evaluation rangeflashing: switch point programming, object detected LED redsolid: errorflashing: switch point programming, object not detected Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 40 mA Power consumption≤ 400 mW Time delay before availability≤ 300 ms Interface Interface typeIO-Link (via C/Q = Pin 4) Device profileSmart Sensor Transfer rateCOM2 (38.4 kBit/s) IO-Link Revision1.1 Min. cycle time2.3 ms Process data width16 bit SIO mode supportyes Device ID0x300300 (3146496) Compatible master port typeA Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level2.5 V ... UB Input impedance> 22 kΩ Output rated operating currentcurrent source < 2.5 mA Pulse length≥ 1 ms with external control, low active Synchronization frequency Common mode operation≤ 141 Hz Multiplex operation≤ 141 Hz / n , n = number of sensors , n ≤ 10 Output Output type1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Rated operating current100 mA , short-circuit/overload protected Voltage drop≤ 2.5 V Repeat accuracy≤ ± 0.1 % of full-scale value Switching frequencyfactory setting: 20 Hz programmable max. 45 Hz Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm Temperature influence≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0,17 %/K (without temperature compensation) Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 IEC 61131-9:2013 Approvals and certificates UL approvalcULus Listed, Class 2 Power Source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typeConnector plug M8 x 1 , 4-pin Degree of protectionIP67 Material HousingPolycarbonate Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Installation positionany position Mass9 g Tightening torque, fastening screwsmax. 0.2 Nm Factory settings Outputnear switch point: 25 mm far switch point: 250 mm Output mode: Window mode Output logic: normally open Beam widthwide Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960 Datasheet excerpt: Technical data of  UC250-F77-EP-IO-V31 Product Description Single head system General specifications Sensing range20 ... 250 mm Adjustment range25 ... 250 mm Dead band0 ... 20 mm Standard target plate10 mm x 10 mm Transducer frequency400 kHz Response delayminimum : 8 ms factory setting: 29 ms Sensor cycle time≥ 8 ms (factory setting) ; programmable to 60 s Memory Non-volatile memoryEEPROM Write cycles300000 Indicators/operating means LED greensolid: Power onflashing: Standby mode or IO-Link communication LED yellowsolid: object in evaluation rangeflashing: switch point programming, object detected LED redsolid: errorflashing: switch point programming, object not detected Electrical specifications Operating voltage10 ... 30 V DC , ripple 10 %SS No-load supply current≤ 40 mA Power consumption≤ 400 mW Time delay before availability≤ 300 ms Interface Interface typeIO-Link (via C/Q = Pin 4) Device profileSmart Sensor Transfer rateCOM2 (38.4 kBit/s) IO-Link Revision1.1 Min. cycle time2.3 ms Process data width16 bit SIO mode supportyes Device ID0x300300 (3146496) Compatible master port typeA Input/Output Input/output type1 synchronization connection, bidirectional 0 Level0 ... 1 V 1 Level2.5 V ... UB Input impedance> 22 kΩ Output rated operating currentcurrent source < 2.5 mA Pulse length≥ 1 ms with external control, low active Synchronization frequency Common mode operation≤ 141 Hz Multiplex operation≤ 141 Hz / n , n = number of sensors , n ≤ 10 Output Output type1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected Rated operating current100 mA , short-circuit/overload protected Voltage drop≤ 2.5 V Repeat accuracy≤ ± 0.1 % of full-scale value Switching frequencyfactory setting: 20 Hz programmable max. 45 Hz Range hysteresis1 % of the adjusted operating range (default settings), programmable , min. 1 mm Temperature influence≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0,17 %/K (without temperature compensation) Compliance with standards and directives Standard conformity StandardsEN 60947-5-2:2007+A1:2012 IEC 60947-5-2:2007 + A1:2012 IEC 61131-9:2013 Approvals and certificates UL approvalcULus Listed, Class 2 Power Source CCC approvalCCC approval / marking not required for products rated ≤36 V Ambient conditions Ambient temperature-25 ... 70 °C (-13 ... 158 °F) Storage temperature-40 ... 85 °C (-40 ... 185 °F) Mechanical specifications Connection typeConnector plug M8 x 1 , 4-pin Degree of protectionIP67 Material HousingPolycarbonate Transducerepoxy resin/hollow glass sphere mixture; polyurethane foam Installation positionany position Mass9 g Tightening torque, fastening screwsmax. 0.2 Nm Factory settings Outputnear switch point: 25 mm far switch point: 250 mm Output mode: Window mode Output logic: normally open Beam widthwide Classifications SystemClasscode ECLASS 11.027272803 ECLASS 10.0.127272803 ECLASS 9.027272803 ECLASS 8.027272803 ECLASS 5.127272803 ETIM 8.0EC001849 ETIM 7.0EC001849 ETIM 6.0EC001849 ETIM 5.0EC001849 UNSPSC 12.141111960